« 2026年10月 | トップページ

2026年11月

2026年11月15日 (日)

Keyhole Spoke Holes (Rear Hub)

次回、この記事の日本語版を投稿します。

Vintage Japanese bicycle rear hubs are known for their unique shaped spoke holes.Img_0340
Img_0341

Let's take a look at two examples and the reasons behind the design.
Img_1410

First is a pre-WWII model.
Img_1412

Note the stamp on the cap "OIL".
Img_1411 
Img_1407

The second is from the 1950s.
Img_1414

Note the grease nipple.
Img_1413
 Img_1405

These spoke holes are often referred to as "keyhole" shaped spoke holes.
There are three main reasons for this design.

1. British Influence
The Japanese adopted many of the British designs for their bicycles, including the keyhole shaped spoke holes on rear hubs.
It is interesting to notes that today's bicycles have the same number of spokes (72); however, the ratio on today's bicycles is divided evenly with 36 in the front and 36 in the rear.  Whereas, on vintage bicycles, the ratio was 32 in the front and 40 in the rear.  The reason was simple, bicycles were used for work, were equiped with large rear luggage (carrier) racks and had to carry heavy loads so additional support was required for the rear wheel. 

2. Necessity
In 1952 less than 14% of all roads in Japan were paved.
However, that percentage jumped to 57% by 1965, 79% by 1975 and surpassed 90% by 2018.
P1120440  
P1120856
Due to the impact from poor road conditions, heavy overloading, and the limitations in the quality of steel and heat-treatment processes available at the time, rear-wheel spokes broke far more frequently.

3. Ease of spoke installation
The beauty of the keyhole shaped spoke hole is that it allows a spoke to be replaced without having to remove the freewheel or band brake.  Consider modern hubs which have a tiny hole whose diameter is just a fraction wider than the spoke itself.

The problem is that in order to thread the spoke through the spoke hole the freewheel or band brake gets in the way. While it is possible to thread the spoke by severely bending it, this compromises spoke strength.

With the keyhole design, the spoke head (elbow) goes through the larger (middle) section of the hole and then slid into the narrower, slotted section.  This makes it possible to easily install a spoke without having to remove the freewheel or band brake.Img_1423
Img_1424

Img_1418
Img_1419

Lastly, tt is also interesting to note that wheel building was done in the opposite way.  On today's bicycles the spokes are first inserted through the holes in the hub and then laced to the rim holes where a nipple is attached.

With the keyhole design, first a washer and nipple are attached to each spoke, inserted through the rim holes from the outside, and the spoke head (elbow) is then laced to the holes in the rear hub. 

 

 

2026年11月 1日 (日)

ノザワ28番 内装3段 高級スポーツ車 (第4)

I'll be back with another English post soon until then stay trued and happy wheels.

この連載の第2及び第3では、極めて希少な「ノザワNo.28 3段内装変速付き高級スポーツスター」について引き続き取り上げました。

ある倉庫の奥隅にひっそりと置かれ、65年もの間眠り続けていたところを発見されました。
Img_0936b

こうした「スポーツスター」モデルは、日本における自転車が実用重視からレジャーへと移行しつつあった1950年代後半から1960年代初頭にかけて人気を博しました。

この連載の最終回では、「ノザワNo.28 3段内装変速付き高級スポーツスター(第1) 」で取り上げた1959年版ノザワ自転車製作所カタログの仕様と、この自転車の仕様がいかに酷似しているか、その比較を締めくくります。

シマノ製3段内装変速ハブ「3.3.3.」が装備されています。
Img_0964_20261016095701

シマノ 3.3.3. ラベル(クロームメッキの輝きに注目)
自転車が一度も乗られることなく、65年間眠り続けていたことの証である。
Img_0950_20261016095701

油注入口付き
Img_0933_20261016095701

リアブレーキはバンドブレーキ(1959年カタログの仕様と同様)
ノザワ商標刻印
Img_0952_20261016095701

ロックもノザワ商標刻印入り
Img_0948_20261016095701

ノザワ商標刻印入りリア反射板 
Img_0951_20261016095701  

これでノザワ28番 内装3段 高級スポーツ車の連載終了です。
持ち主が手放すそうなので、ご興味がある方はメールして下さい。

« 2026年10月 | トップページ